1. Height of the Instrument method is a less tedious and simple process.
a) True
b) False
Explanation: The above statement is true because it involves simple calculations when compared to Rise and fall method, which can be completed with minimal effort.
2. While doing construction work, which among the following is more suitable?
a) Rise and Fall method
b) Traversing
c) Height of the Instrument method(H.I)
d) Compass Surveying
Explanation: Height of the Instrument method is less tedious than Rise and fall method. Moreover, this process is suitable for taking numerous readings from same instrument setting. Traversing is a process of establishing control points and Compass surveying involves in finding the bearings.
3. The formula for calculating R.L can be given as _________
a) H.I+F.S
b) H.I-F.S
c) H.I-B.S
d) H.I+B.S
Explanation: By subtracting the fore sight value from height of the instrument, the value of reduced level for the next set of reading can be obtained.
4. Which of the following indicates the formula for arithmetic check?
a) ΣB.S-ΣF.S=Last R.L-First R.L
b) ΣF.S-ΣB.S=Last R.L-First R.L
c) ΣB.S+ΣF.S=First R.L-Last R.L
d) ΣF.S+ΣB.S=Last R.L-First R.L
Explanation: If the difference in summation of back sight and fore sight is equal to the difference of last R.L and first R.L, then obtained set of values for finding difference in elevation are correct.
5. Rise and fall method provides check in calculations for all sights?
a) true
b) false
Explanation: Since the check for intermediate sights is not available in H.I method, it may lead to errors while doing calculations.
6. Which of the following represents a form of Bench Mark (B.M)?
a) True Benchmark
b) Assumed Benchmark
c) Datum
d) Arbitrary Benchmark
Explanation: Benchmark is a point of known elevation taken as reference. It is classified as Arbitrary, G.T.S, Permanent and Temporary.
7. If the staff at the station point is not held vertically, the R.L at the observation would be ______________
a) Less than true R.L
b) Greater than true R.L
c) Equal to the true R.L
d) Two times the true R.L
Explanation: Due to irregular holding of the staff, the values which are obtained by the levelling instrument might lead to decrease in R.L.
8. If the R.L of a B.M is 100m and back sight is 1.225m, find the H.I at the station?
a) 101.225m
b) -101.225m
c) 98.775m
d) -98.775m
Explanation: We know that, H.I=R.L+B.S
Then, H.I= 100+1.225 H.I=101.225 m.
9. The combined correction for curvature and refraction can be given as _______
a) C = 14d2/6R
b) C = 6d2/7R
c) C = 7d2/2R
d) C = 6d2/14R
Explanation: By subtracting the correction due to curvature from correction due to refraction we can get the combined correction i.e., \(C = \frac{d^2}{2R} – (\frac{1}{7}*\frac{d^2}{2R}).\)
10. Find the correction for curvature and correction for refraction, if the value of d = 2400 m?
a) 0.425, 0.604
b) 0.452, 0.064
c) 0.064, 0.452
d) 0.604, 0.425
Explanation: Correction for curvature = \(\frac{d^2}{2R} = \frac{2.4^2}{2*6370}*1000 = 0.452m\) Correction for refraction \( = \frac{1}{7} * C_c = \frac{0.452}{7} = 0.064m.\)